315 LBS Outboard Boat Motor Stand Carrier Cart Dolly Storage Pro Heavy Duty

Yamaha 25hp 1998 4 stroke.
I bought this motor stand since it was rated to hold my motor. It barely does.
Cons;
- instructions were garbage but with basic know how, look at the picture and you can figure it out.
- the weight of the motor makes the plastic tires go flat after sitting a while which makes it difficult to roll. Will hardly roll over anything other than concrete.
- IMPORTANT!! the weight of the motor make it want to tip forward on either corner of the front wheels if they are not locked into place well.
Pros: it serves as a mount if that's all it's intended for is to sit in the garage for a while.
What I'd change or upgrade.
: Go to harbor freight or northern tool and get some beefed up tires to help support and easily roll around with for the back tires.
The fronts I'd do the same but with the locks on the tk prevent it from tipping.

Easy to put together using pic. No written instructions. Have not put motor on yet

If you follow assembly instructions, this stand will work well

Nice stand. I have a 5 hp , a 7hp and a trolling motor+ gas tanks all hanging on it. Easy to move around.

I have a smaller 2.3 hp outboard motor on the stand. The stand is very top heavy and begins to fall backwards very easily. Looking at it it is tilted backwards. Either the back wheels should be at least an inch larger or the front wheels smaller. Gotta add weight to front of stand to help balance it out.

Product is as described & works perfectly!

it will do the job it’s required for and it’s a fraction of the cost of other versions

Final 2 cents after 14 days:
For the money, it ain't bad.
Fabricated 3 cross bars.
I added a horizontal cross bar just ahead of the rear wheels and the other 2 other cross bars to the rear vertical tubes ( 1 just above the rear wheels, 1 just below where the vertical tubes intersect with the tubes for the handle bar), the cart stiffened up quite a bit. So, stronger front casters and the 3 cross bars made the unit what it should be.

This Product is very easy to set up and Looks very cool. Love it!

The stand arrived ahead of schedule, it was easy to assemble.

The product itself is sturdy and nice, but the price is too expensive in my view.

easily moved from room to room.

It's convenient to use, but I think it will be better if the price is lower.

I have a smaller 2.3 hp outboard motor on the stand. The stand is very top heavy and begins to fall backwards very easily. Looking at it it is tilted backwards. Either the back wheels should be at least an inch larger or the front wheels smaller. Gotta add weight to front of stand to help balance it out.

Just what we needed. Great price.

Exactly as advertised.

No assembly instructions included, but I found pictures on the internet so I eventually got it together. But it is kind of crooked, I don’t know for sure but it seems like I got two of the same handles, whereas there should be a right and left. Ended up taking too much time to put together, it works, I’ve got my motor on it just fine, but I wouldn’t purchase again.

This motor stand is perfect for someone who isn't a pro and moving motors all day. It's hobbyist grade but will hold a motor for you during winter storage or while you are doing a repair. Mine came without instructions, but the picture is enough for anyone handy to assemble. I wouldn't recommend this for a motor any bigger than a 20hp. The tubular frame isn't sturdy enough to handle a motor much larger than a 20hp.

A very useful tool, it feels good after a long time.

Product assembled easily but one of the parts did not fit properly so I made one to complete the assembly. Otherwise the product performs well and I have no complaints.

Well built . Directions a little schetchy.

works as advertised. pleased with the product

Working well so far for my 10HP yamaha outboard. I fit a small recycle can in between for flushing it. Happy with it for the price.

Sturdy, simple, easy to put together

Not sure I would call this stand 'heavy duty' but it works great for my old 1hp & 2 hp outboards

Easy to assemble, sturdy with my 15 hp Mercury.

This is a well made product. Works very well to transport my boat motor.

I haven't completed the assembly of the motor stand but it should work fine for my 15hp Johnson short shaft.

It seem cheap but it works great for the purpose

Just the basics of what we needed. Relatively easy to assemble. Using it for our new 6 hp Suzuki outboard.

Good value for the price. There are no step by step assembly instructions but it’s pretty easy to figure out. Our motor is 5 hp and only about 70 pounds so the cart is more than adequate. I had a question about the parts, sent a message and they were extremely responsive. Satisfied with the purchase.

have a small outboard on it and it almost wants to tip backward. not a hard build but no instructions leave you wondering a bit.

works perfect directions were not helpful really at all besides that its held every outboard ive put on it up to a 4 stroke 8hp mercury added something to hold the legs outward a little more you don't have to do that though works fine with out that

Works as advertised

A bit complicated to assemble but came out fine in the end.

Works great. Seems to hold 60hp motor fine.

This is a sturdy and stout engine stand for the money. And no you don't need any fabricating skills, as one ridiculous review stated. It's perfectly adequate as designed. The diagram included doesn't give any instructions as to how to assemble. However it's pretty simple to figure out based on the picture. The nylon nuts are a pain to torque using a Flathead and Ratchet as I did. Great stand would definitely recommend it!

Best outboard motor stand I own. Perhaps the best one on the market. Hahahahaha C’mon man

Best outboard motor stand I own. Perhaps the best one on the market.HahahahahaC’mon man

Just what i needed to maneuver my 9.9 Merc. Only knock is no wheel lock.

Works great!

Needs additional cross brace by the wheels.

works good ,i like it holds my 15 hp motor ,wheels it around nice and easy

Needed better installation instructions. Way to complex to guess!!!!

I have an Evinrude 88 SPL that is right around 300lbs. I had to remove it to work on my transom. When this came in I was sceptical that it would be able to hold the motor. To my surprise it is able to support it. I would not feel comfortable doing too much wrenching on the motor while on this stand. It works as a storage device. If you're motor is closer to 200lbs or less I think you'll be happy with it. Still for 50 bucks it works.

Holds my 40 hp Yamaha 2-stroke just fine, can wheel it around in the shed. Suits my need.

worked grate

Easy to put together. Works well.LOVE IT!

Easy to put together. Works well.LOVE IT!

Sturdy construction, good value, but no assembly instruction, just a crude drawing

This is a sturdy and stout engine stand for the money. And no you don't need any fabricating skills, as one ridiculous review stated. It's perfectly adequate as designed. The diagram included doesn't give any instructions as to how to assemble. However it's pretty simple to figure out based on the picture. The nylon nuts are a pain to torque using a Flathead and Ratchet as I did. Great stand would definitely recommend it!

Better than I expected

Worth the price

Easy Assembly well packaged

Easy Assemblywell packaged

Works great areal good deal.

Works great for my 90 lb, 9.9 Honda

Just what I wanted for my outboard motor.

These carriers are very nice, I bought 2 and they are easy to assemble. Very sturdy and does the trick whenever I need to transport. I would recommend this product.

For what I paid for it. It's great and does the job.

So far so good my only issues are the wheels they're pure junk.

as expected

Perfect !

Excellent product

Put it together set a 30hp motor on and it works great

Great stand. Easy to put together. Set outboard motor on and wheeled it around with ease. Highly recommend.

Serves it's? purpose for 10HP outboard. Not the strongest material but good enough for what I need. Poor directions but it can be figured out fairly easy.

Worked very well .

good

The motor stand is very good for the money. It is stronger than the aluminum stand it replaced, and less expensive. It works great for my 15 hp Evinrude. It can be made significantly better with a few easy modifications. I replaced the wheels with pneumatic tires from Harbor Freight ($8.00 each), and added a brace in parallel with the axel. I would have gladly paid more to get these options, and would have rated it 5 stars.

Great looking stand. Rolls well, assembly takes about 5 minutes. Supports a 210lb outboard with ease.

Great stand,super sturdy.

Easy to assemble. Sturdy and steady to maneuver. Outboard has a new winter home. Thanks

We had to move an outboard boat motor and this stand help tremendously since outboard boat motors are very heavy.

Very pleased with quick delivery and great quality.

Easy to put together, sturdy, strong, steady and rolls effertlessly across garage floor with & without boat motor. Perfect for what we wanted.

After a few changes and replacing some of the bolts that came with it everything went well. Some of the bolts and nuts stripped out as I was tightening them down went to the Local Hardware store bought new.

The support on the handlebars was too short otherwise I would have given it 5 stars

good buy for smaller motor like 9.9 4 stroke.